After thermal desorption, treated soil is generally reusable. Contaminants are destroyed or driven off during treatment, so the mineral material retains its fundamental properties. Whether and how the soil can be used after treatment depends on the results of the final quality assessment. The following sections answer the most important questions about the fate and quality of the treated material.
Is desorbed soil reusable after treatment?
Yes, thermally desorbed soil is fundamentally reusable after successful treatment. Because thermal desorption takes place in the absence of oxygen at temperatures of up to approximately 600 °C, organic contaminants are destroyed or converted to a gaseous state without permanently damaging the mineral grain structure of the soil. The result is a largely contaminant-free mineral material.
The final analysis is decisive for actual reusability. Only once laboratory values confirm that the treated soil complies with applicable limit values can it be classified as a secondary raw material and put to new use. The recycling of soil is not a side effect but a central goal of thermal soil treatment: valuable mineral resources remain in circulation instead of being permanently landfilled.
What quality checks does the soil undergo after desorption?
After thermal desorption, the treated soil undergoes a multi-stage quality assessment. Samples are taken and analyzed in the laboratory for the relevant contaminant parameters that were identified as pollutants prior to treatment. Only once the analytical values fall below the legally prescribed limit values is the material considered properly treated.
The assessment is guided by the relevant standards and regulations, including the Federal Soil Protection and Contaminated Sites Ordinance (BBodSchV) and the LAGA assignment values. Different limit values may apply depending on the intended use. Soil intended for use in noise protection embankments is subject to different requirements than material used in road construction. The quality management system ensures that testing processes are documented, traceable, and compliant with regulatory requirements.
Where is treated soil used after thermal desorption?
Thermally treated soil is used primarily as mineral backfill material in civil and earthworks engineering. Typical applications include the backfilling of excavation pits, path construction, landscaping, and use as sub-base material in road construction. In each case, the prerequisite is that the analytical values meet the requirements of the respective installation site.
In some cases, the treated material is also suitable for the recultivation of land, for example as part of the aftercare of post-mining landscapes or the design of compensatory areas. Particularly in regions with an intensive mining history, such as central Germany, there is a high demand for suitable backfill material. Treated soil can make a valuable contribution to sustainable land use here, provided the quality requirements are met. If recovery is not possible, the material is sent for regulated disposal.
What happens to contaminants that become gaseous when heated?
Contaminants that transition to a gaseous state during thermal desorption are treated in a multi-stage exhaust gas cleaning system. The contaminated process gas leaves the rotary kiln and passes sequentially through a dust removal stage, thermal post-combustion, flue gas scrubbing, and an activated carbon filter. At the end of this process, statutory emission limit values are reliably met.
Thermal post-combustion is the central step: gaseous contaminants are completely oxidized and thus destroyed at high temperatures. Compounds such as TPH, BTEX, PAH, PCB, or dioxins and furans (PCDD/PCDF) are safely eliminated in this way. The downstream flue gas scrubber removes acidic gas components, and the activated carbon filter binds any remaining trace substances. This interplay of cleaning stages makes thermal desorption one of the most effective processes for treating complexly contaminated soils.
What distinguishes thermal desorption from other soil remediation processes?
Thermal desorption differs from other soil remediation processes above all in the range of treatable contaminants and the depth of treatment. While biological processes only capture biodegradable compounds and chemical-physical methods are often limited to specific groups of substances, thermal desorption enables the simultaneous treatment of a broad spectrum of contaminants.
Another key difference lies in the outcome: thermal desorption destroys organic contaminants or drives them completely out of the soil material. Biological processes, by contrast, only partially degrade contaminants and require significantly longer treatment periods. Soil washing can dissolve contaminants from the soil, but in doing so generates contaminated water streams that must be treated separately. Thermal desorption in a rotary kiln is also site-independent: the material is transported to the facility and treated there under controlled conditions, ensuring consistently high treatment quality.
Which types of waste can be thermally treated together with soils?
In addition to contaminated soils, a thermal desorption facility can also treat construction rubble, dredged material, and mineral process residues such as slags, ashes, sludges, and dusts. The prerequisite is that the materials are mineral in nature and exhibit the approved contaminant parameters.
This opens up possibilities for comprehensive material flow management: various waste fractions from a remediation project can be collected, temporarily stored, and treated together. Typical areas of application are the remediation of decommissioned industrial and gasworks sites, where contaminated construction rubble and process residues arise alongside soils. Which materials can be treated in individual cases depends on the composition, contaminant profile, and regulatory approvals. A precise characterization of the waste prior to acceptance is therefore always required.
How ARE Deutzen GmbH helps with the recovery of treated soils
ARE Deutzen GmbH, as a specialized waste management company, offers a complete solution for the thermal treatment of contaminated mineral waste, from acceptance through to the verified recovery or disposal of the treated material. The range of services specifically includes:
- Thermal soil treatment in a rotary kiln at temperatures of up to approximately 600 °C, depending on the material and contaminant load, in the absence of oxygen
- Treatment of a broad spectrum of contaminants, including TPH, BTEX, PAH, PCB, PFAS/PFOS, dioxins, cyanides, and other chlorinated hydrocarbons
- Multi-stage exhaust gas cleaning to reliably comply with statutory emission limit values
- Analysis and quality assessment of the treated material in accordance with applicable regulations
- Material flow management for various mineral waste fractions from a single project
- Over 30 years of experience and more than 2.5 million tonnes of treated mineral materials
If you would like contaminated soils or mineral waste treated safely and verifiably, contact ARE Deutzen directly. Our specialists will advise you on acceptance requirements, treatment options, and the subsequent fate of the material.